Web Catalogue update October 2019

DIGITAL TYRE INFLATOR 11 1881 NZ. pub. 11/16 © Digital Tyre Inflator with easy-to-read LCD display. • 4 unit settings (BAR, PSI, KPA, KGF). • 1.5m hose. • Comfortable rubber grip. • Clip-on air chuck. • Grip mounted inflation / deflation lever. • Back light feature. • Measuring range: 0-12BAR (0-175PSI). • Reading accuracy is 0.01BAR (0.1PDI). • Max. inlet pressure is 15 BAR (218PSI) • Battery 2x AAA Description Art. No. Pack Qty. Digital Tyre Inflator 0715 54 071 1 Instructions: 1. Remove tyre valve cap. 2. With clip-on air lever depressed, firmly press chuck onto tyre valve stem and release lever, ensure that there are no air leaks. 3. Press the grip to inflate, press the grip half-way to deflate. 4. On: Press the on/unit/light button to turn on the inflator. If the unit is left idle, it will turn off automatically after 90 seconds. 5. Backlight: When the inflator is on, press the on/unit/light button to turn on the backlight. The backlight will extinguish automatically after 5 seconds. The backlight will not be activated by turning on the inflator. 6. Unit Change: Press and hold the on/ unit/light button for 3 seconds, enter unit change mode, then press on/unit/ light button to choose the desired unit of measurement. The unit chosen will be the default unit for the following usage. 7. The inflator‘s voltage is 2.4 - 3.6 DC, if the voltage is below 2.4 V, the low battery signal on the top left will flash continuously to remind the user to change the battery. Important: To avoid the risk of personal injury, especially to the eyes, face or skin, DO NOT direct the stream at any person. Please note: • Device has been calibrated according to EN12645:1998. • Includes 2x AAA alkaline batteries. DIGITAL TYRE INFLATOR 11 1881 AUS. pub. 03/15 © Digital Tyre Inflator with easy-to-read LCD display. • 4 unit settings (BAR, PSI, KPA, KGF). • 1.5m hose. • Comfortable rubber grip. • Clip-on air chuck. • Grip mounted inflation / deflation lever. • Back light feature. • Measuring range: 0-12BAR (0-175PSI). • Reading accuracy is 0.01BAR (0.1PDI). • Max. inlet pressure is 15 BAR (218PSI) • Battery CR2450. Description Art. No. Pack Qty. Digital Tyre Inflator 0715 54 071 1 Instructions: 1. Remove tyre valve cap. 2. With clip-on air lever depressed, firmly press chuck onto tyre valve stem and release lever, ensure that there are no air leaks. 3. Press the grip to inflate, press the grip half-way to deflate. 4. On: Press the on/unit/light button to turn on the inflator. If the unit is left idle, it will turn off automatically after 90 seconds. 5. Backlight: When the inflator is on, press the on/unit/light button to turn on the backlight. The backlight will extinguish automatically aft r 5 seco ds. The backlight will not be activated by turning on the inflator. 6. Unit Change: Press and hold the on/ unit/light button for 3 seconds, enter unit change mode, then press on/unit/ light button to choose the desired unit of measurement. The unit chosen will be the default unit for the following usage. 7. The inflator‘s voltage is 2.4 - 3.6 DC, if the voltage is below 2.4 V, the low battery signal on the top left will flash continuously to remind the user to change the battery. Important: To avoid the risk of personal injury, especially o the eyes, face or skin, DO NOT direct the stream at any person. Please note: • Device has been calibrated according to EN12645:1998. • Wurth encourage the frequent re-calibration of the gauge to ensure absolute accuracy. Currently this service is not available through Wurth Australia. • Includes free spare battery. Spare battery CR2450 3V Art. No. 0827 082 450 Spare air chuck and hose set Art. No. 0715 54 087 Extended fitting for trucks Art. No. 0715 54 086 Battery Change Instructions Unscrew with cross screwdriver Open LCD panel with flat screwdriver Change battery Install the LCD panel Screw the back DIGITAL TYRE INFLATOR 11 1881 AUS. pub. 03/15 © Digital Tyre Inflator with easy-to-read LCD display. • 4 unit settings (BAR, PSI, KPA, KGF). • 1.5m hose. • Comfortable rubber grip. • Clip-on air chuck. • Grip mounted inflation / d flation lever. • Back light feature. • Measuring range: 0-12BAR (0-175PSI). • Reading accuracy is 0.01BAR (0.1PDI). • Max. inlet pressure is 15 BAR (218PSI) • Battery CR2450. Description Art. No. Pack Qty. Digital Tyre Inflator 0715 54 071 1 Instructions: 1. Remove tyre valve cap. 2. With clip-on air lever depressed, firmly press chuck onto tyre valve stem and r lease l ver, ensure that there are no air leaks. 3. Press the grip to inflate, press the grip half-way to deflate. 4. On: Press the on/unit/light button to turn on the inflator. If the unit is left idle, it will turn off automatically after 90 seconds. 5. Backlight: When the inflator is on, press the on/unit/light button to turn on the backlight. The backlight will extinguish automatically after 5 seconds. The backlight will not be activated by turning on the inflator. 6. Unit Change: Press and hold the on/ unit/light button for 3 seconds, enter unit change mode, then press on/unit/ light button to choose the desired unit of measurement. The unit chosen will be the default unit for the following usage. 7. The inflator‘s voltage is 2.4 - 3.6 DC, if the voltage is below 2.4 V, the low battery signal on the top left will flash continuously to remind the user to change the battery. Important: To avoid the risk of personal injury, especially to the eyes, face or skin, DO NOT direct the stream at any person. Please note: • Device has been calibrated according to EN12645:1998. • Wurth encourage the frequent re-calibration of the gauge to ensure absolute accuracy. Currently this service is not available through Wurth Australia. • Includes free spare battery. Spare battery CR2450 3V Art. No. 0827 082 450 Spare air chuck and hose set Art. No. 0715 54 087 Extended fitting for trucks Art. No. 0715 54 086 Battery Change Instructions Unscrew with cross screwdriver Open LCD panel with flat screwdriver Change battery Install the LCD panel Screw the back AAA Alkaline Battery (2x required) Art. No. 0827 111